Fein Nibbler BLK 1.6 E 72323860120 16 Gauge Sheet Metal (350W Motor 360 Degree Rotating Head QuickIN System Corrugated Trapezoid Cutting Tool)
Couldn't load pickup availability
Fein BLK 1.6 E 72323860120 16-Gauge Universal Sheet Metal Nibbler
The Fein BLK 1.6 E 72323860120 Universal Sheet Metal Nibbler executes distortion-free, burr-free profile cutting across 16-gauge mild steel and 22-gauge stainless steel sheets. Powered by a continuous-duty 350W industrial motor delivering a linear cutting speed of 6.2 ft/min, this metal fabrication tool incorporates a 360-degree tool-free rotatable punch head that indexes in 45-degree steps to maneuver around deep corrugated folds and trapezoidal roof profiles. A proprietary QuickIN system enables instant, wrench-free punch and die replacements, while the slim-grip motor housing and extra-long 16-foot power cord maximize operator control in overhead commercial ductwork and roofing installations.
Best Used For:
- Corrugated & Trapezoidal Roofing Panels: Cutting standing seam ridges, valley flashing, and corrugated sheet profiles up to 16 gauge without deforming the painted metal finish.
- HVAC Duct & Transition Cutouts: Sizing tight circular collars and rectangular register drop-in openings in sheet metal duct assemblies with smooth directional navigation.
- Stainless Steel & Enclosure Modification: Nibbling internal cutouts in 22-gauge stainless electrical cabinets and machinery guards without producing hazardous flying sparks.
Key Performance & Safety Features
- 360-Degree Tool-Free Rotating Head: Locks at 45-degree intervals to alter cutting trajectories effortlessly along complex panel ribbing and tight radiuses.
- QuickIN Rapid Tool-Less System: Swaps out worn punches and dies in seconds without requiring wrenches or hex keys to eliminate jobsite downtime.
- High-Torque 350W German Motor: Drives consistent stroke power at 6.2 ft/min to maintain cutting speed through tough alloys without motor stalling.
- Rotating Punch Wear Distribution: Dynamic punch movement delivers up to 30% longer service life by evening out localized friction wear.
- Narrow Drive Nose Profile: Ultra-slim gearbox clearances pass cleanly over deep profile folds where conventional shears bind.
- Protective Air Vent Mesh: High-density metal mesh over motor ventilation ports prevents falling metallic chips and swarf from shorting internal armatures.
What's Included
- (1) Fein BLK 1.6 E Universal Sheet Metal Nibbler (72323860120)
- (1) QuickIN Punch (Pre-Installed)
- (1) QuickIN Die for Corrugated and Trapezoidal Sheet (Pre-Installed)
- (1) Heavy-Duty 16-Foot (5 m) Rubber Power Cord
Technical Specifications
| Specification | Detail |
|---|---|
| Model Number | BLK 1.6 E (72323860120) |
| Motor Power Consumption | 350 Watts |
| Mild Steel Capacity (400 N/mm²) | 16 Gauge (0.063 in / 1.6 mm) |
| Stainless Steel Capacity (600 N/mm²) | 22 Gauge (0.028 in / 0.7 mm) |
| Aluminum Capacity (250 N/mm²) | 12 Gauge (0.100 in / 2.5 mm) |
| Linear Cutting Feed Rate | 6.2 ft/min (1.9 m/min) |
| Cutting Head Articulation | 360° Tool-Free Rotation in 45° Detents |
| Tool Change Mechanism | Fein QuickIN Rapid Punch/Die Release |
| Power Cord Length | 16.0 ft (5.0 m) Industrial Rubber Cable |
| Substrate Suitability | Corrugated Steel, Trapezoidal Sheets, Stainless Plate, HVAC Duct, Aluminum |
| Debris Safety | Integrated Chip Protection Mesh on Motor Vents |
Pro-Tip: Apply a continuous light coat of cutting oil along your layout lines when cutting stainless steel; lubricating the punch and die decreases cutting resistance and prevents work-hardening of the metal edge.