Klein 32614 precision pocket screwdriver assembled with bit tip extended and ready for delicate low-voltage electrical work.
Diagram detailing Klein 32614 driver features, including swivel cap, sliding pocket cuff, short/long reversible barrel, and double-ended bits.
Diagram showing the Klein 32614 sliding yellow cuff mechanism sliding forward to conceal driver bits for safe pocket storage.
Klein Tools 32614 precision driver configured with its extended 2.09-inch long shaft for deep terminal screw access.
Klein Tools 32614 precision driver configured in short-reach position with a #0 Phillips bit loaded in its yellow Cushion-Grip handle.
Klein Tools 32614 electronics driver with sliding protective collar extended, safely hiding the bit tip for pocket transport.
Klein 32614 driver handle alongside its removable double-ended steel shank loaded with micro Phillips and slotted driver bits.
Klein 32614 pocket driver components fully disassembled into yellow handle, aluminum barrel, and two double-ended precision bits.
Technician using the extended-reach Klein 32614 driver to tighten wire connection screws on an electronic circuit board module.
Worker swapping bit orientations on the Klein 32614 precision driver by pulling the double-ended steel shaft out of the aluminum sleeve.
Technician sliding the yellow protective collar forward on a Klein 32614 driver to conceal the metal bit tip for safe pocket storage.
Klein 32614 precision driver clipped into a shirt pocket with its tip fully concealed by the sliding collar to prevent fabric tears.
Pocket Drivers, 4-in-1 Electronics and 3-in-1 HVAC promotional video
Klein 32614 precision pocket screwdriver assembled with bit tip extended and ready for delicate low-voltage electrical work.
Diagram detailing Klein 32614 driver features, including swivel cap, sliding pocket cuff, short/long reversible barrel, and double-ended bits.
Diagram showing the Klein 32614 sliding yellow cuff mechanism sliding forward to conceal driver bits for safe pocket storage.
Klein Tools 32614 precision driver configured with its extended 2.09-inch long shaft for deep terminal screw access.
Klein Tools 32614 precision driver configured in short-reach position with a #0 Phillips bit loaded in its yellow Cushion-Grip handle.
Klein Tools 32614 electronics driver with sliding protective collar extended, safely hiding the bit tip for pocket transport.
Klein 32614 driver handle alongside its removable double-ended steel shank loaded with micro Phillips and slotted driver bits.
Klein 32614 pocket driver components fully disassembled into yellow handle, aluminum barrel, and two double-ended precision bits.
Technician using the extended-reach Klein 32614 driver to tighten wire connection screws on an electronic circuit board module.
Worker swapping bit orientations on the Klein 32614 precision driver by pulling the double-ended steel shaft out of the aluminum sleeve.
Technician sliding the yellow protective collar forward on a Klein 32614 driver to conceal the metal bit tip for safe pocket storage.
Klein 32614 precision driver clipped into a shirt pocket with its tip fully concealed by the sliding collar to prevent fabric tears.
Pocket Drivers, 4-in-1 Electronics and 3-in-1 HVAC promotional video
KLEIN TOOLS

Klein Tools Electronics Pocket Screwdriver 32614 4 in 1 Precision Driver (Concealable Tip Short Long Shaft Cushion Grip Phillips Slotted Bits)

Only 2 left
SKU: 32614
$15.97 USD

Description

Klein promotional logo logout

Klein Tools 32614 4-in-1 Multi-Bit Precision Electronics Pocket Screwdriver

The Klein Tools 32614 4-in-1 Precision Electronics Pocket Screwdriver functions as a compact manual fastener driving tool engineered to install and remove miniature screws in terminal blocks, control boards, and delicate electronic housings. Weighing 1.6 oz with an overall length of 6-5/8 in., this driver incorporates a retractable sliding collar that conceals the bit tip to protect pockets and prevent tool pouch puncture. Outfitted with a corrosion-resistant anodized aluminum barrel, a smooth-spinning 360-degree swivel cap, and a Cushion-Grip rubber handle, the reversible shank configures into a 0.34 in. short shaft or a 2.09 in. long shaft to hold double-ended heat-treated steel bits covering #0 and #00 Phillips along with 3/32 in. and 1/8 in. slotted sizes.

Best Used For:

  • Delicate Terminal Block Adjustments: Turning small slotted wire clamp screws in low-voltage control circuits, HVAC thermostats, and industrial PLC modules.
  • Circuit Board & Device Assembly: Fastening micro #0 and #00 Phillips screws on circuit boards, electronic relays, and security camera housings.
  • Pocket-Carried Field Maintenance: Carrying a non-puncturing precision driver via integrated pocket clip for immediate diagnostic adjustments in commercial facilities.

Key Performance & Safety Features

  • Sliding Protective Concealment Cuff: Retractable outer sleeve slides forward over the bit shank to shield driver tips and prevent pocket tearing during transport.
  • 360-Degree Rotating Swivel Cap: Independent end-cap rotates freely under palm pressure to deliver precise fingertip torque control on delicate micro screws.
  • Reversible Dual-Length Barrel Shaft: Anodized aluminum barrel flips to offer a 0.34 in. short reach or a 2.09 in. extended reach for deep component access.
  • Precision Ground Steel Micro Bits: Tempered steel bits feature precision-machined tips that fit micro screw heads securely to prevent cam-out and head stripping.
  • Cushion-Grip Rubberized Handle: Ergonomic yellow-and-black rubberized grip provides tactile feedback and maximum manual control when handling small equipment.
  • Integrated Stainless Steel Pocket Clip: Heavy-duty spring-steel clip secures the 0.69 in. diameter screwdriver tightly inside shirt or pants pockets.

What's Included

  • (1) Reversible Driver Handle with Cushion-Grip and Swivel Cap
  • (1) Anodized Aluminum Sliding Concealment Barrel
  • (1) Double-Ended Phillips Bit (#0 / #00)
  • (1) Double-Ended Slotted Bit (3/32 in. / 1/8 in.)

Technical Specifications

Brand Manufacturer Klein Tools®
Model Part Number OEM SKU 32614
Tool Classification Type 4-in-1 Multi-Bit Electronics Pocket Screwdriver
Included Phillips Bit Sizes #00 and #0 Micro Phillips
Included Slotted Bit Sizes 3/32 in. (2.4 mm) and 1/8 in. (3.2 mm) Slotted
Adjustable Shank Reach Lengths Short Position: 0.34 in. (0.9 cm) / Long Position: 2.09 in. (5.3 cm)
Handle Control Mechanism Palm Swivel Cap with Cushion-Grip Rubber Sleeve
Bit Retention Method Quick-Change Mechanical Friction Fit (Non-Magnetic)
Core Metallurgy Materials Heat-Treated Tempered Steel Bits & Anodized Aluminum Barrel
High-Voltage Insulated Frame No (Uninsulated - do not use on energized electrical circuits)
Total Piece Count in Tool 4 Pieces (Handle barrel and 2 double-ended bits)
Overall Tool Dimensions 6.625 in. L x 0.69 in. W x 0.69 in. H (16.8 x 1.8 x 1.8 cm)
Net Weight Specification 0.10 lbs. (1.6 oz. / 45 g)
Global Trade Item Number GTIN 00092644326141

Pro-Tip: When working inside narrow electronic relay racks, pull the aluminum barrel free, reverse it, and insert the long 2.09 in. shaft forward. Pressing your palm against the spinning cap while applying light torque with your fingertips allows you to turn recessed terminal screws smoothly without slipping off the micro screw slot.